I have to think this is a configuration issue, but haven't seen a setting in the arduino's configuration.h that looks plausibly related to this situation. For good measure I even tried a new Mega, with the same result.I even switched out a a new power supply, bupkis. I tried with a new RAMPS and the results were the same. I've confirmed I have 12V going into the 5A input (that powers the onboard heatbed mosfet), but there's only 5V coming out of D8 when the heatbed is turned on in Repetier. When I turn on the heatbed, the RAMPS led lights up, the power supply buzzes, and the temp on the heatbed doesn't climb. I even picked up an separate heatbed mosfet ( Trigorilla).įrom the host, all the controls (x,y,z,extruder and hotend) and sensors (stops and thermistors) work as expected, except for the heatbed. I've done a full replacement of the Melzi. Rather than RMAing the whole thing (which would have been a lot quicker, but much less 'fun'), or just replacing the connectors, I started looking at DIY options. I unplugged everything, let it cool, and found that the heatbed connectors to the Melzi had melted. and then there was smoke from the control box. took the bed a long time to climb to ABS temps. I can prepare and preview designs with it, but when I go to monitor it, it says please connect the pri. 2x Wanhao Duplicator 4x (can't connect) 1x Wanhao Duplicator i3 Plus (Works perfect) 1x Flashforge Dreamer (can't connect) 1x Flashforge Creator 3 (can't connect) 1x Anycubic Chiron (Works perfect) So. I started my first ABS print after a month of PLA prints, and it was struggling to reach temp. Hello, I work at a library and we just had a Wanhao Duplicator 4S donated to us and I am trying to getting it to work with the Cura, I have the printer connected to my computer with a USB cable. With only minor tweaking, it printed PLA great out of the box. I believe my issue to be in the software/configuration, so hoping someone here can help.īackground: I bought a Monoprice Maker Select v2 (aka Wanhao DI3). I've looked everywhere I could online to find an answer, and haven't yet. That's also why I try to chime in when I see 4Ds questions. That's why I have also plugged myself into a CTC group. Good luck on your efforts.īTW, I am with you on wishing there was a better 4Ds community. However, I am looking forward to the day I can have some time to perform the board/hardware transplant and be done with x3g. Everything else I have found seem to be few years old. The OctoPrint plugin I mentioned is the only converter I know of that is being kept up. My recommendation is to spend more time printing with working solutions than trying to develop a new one for an older playing field. While MakerBots work well with their software, I have not had my computer tethered to my printers for over 2 years. I have come to the conclusion that either accept the hoops I have to hop through with x3g or migrate. I used to spend more time trying to research on how to make it work better. Again, I just need to have the time to do it. I did already purchase all the hardware required for me to convert fully to MKS running Marlin. I don't recommend my start and end codes as I know I have some sort of bug in there that requires me to do a "cancel print" in between each good. I did some digging across the internet before I purchased. eBay seller’s description wrote that the 3D printer stalled in the middle of a print. The Duplicator i3 PLUS offers the largest build plate of any 3d printer in it's class With a build volume of just over 200mm x 200mm x 180mm you can build models to. Recently I bough a faulty Wanhao Duplicator 4S to increase the capacity of my 3D printing requirements as I already own one and know the machine inside out. Full-sized SD Card reader for easy file transfers. I did see there was some sort of plugin converter for Slic3r on Windows. 3.25' Touchscreen Control Panel (Wanhao Touch ) with high responsive sensitivity for fast operation. As such, I don't think you can simply output a modified gcode file and expect it to print correctly. What is even stranger, is that Repetier Server will continue to show both printers as connected and the Wanhao printer (the only one that is turned on at this time) will now be controllable through the interface. It has support for duel extrusion, and awesome supports.I digress.Īs for gcode to x3g, my understanding is that there is more than just some command replacement. If I turn the Wanhao off and then on again the crashing will continue (it will stop once I delete the running print job in repetier). I've been using Slic3r for the longest time as the 4Ds is my 2nd printer.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |